We Leave Our Customers Smiling
Ready for 5-Star Level Service?
About half of Newton’s homes were built before 1940, and plenty have been re-insulated, re-windowed, or added onto since. The furnace you’re replacing was sized for the house as it used to be, not the one you live in now. Copying its size is the easy move, and it’s often the wrong one.
When we size furnace replacement in Newton, MA by measuring your space and checking the ductwork you already have, you end up with equipment that matches today’s house. An oversized furnace blasts hot air, shuts off, and repeats, which wastes gas and leaves rooms uneven. A right-sized one runs steadier and keeps the temperature closer from room to room.
Newton’s cold season runs from early December to mid-March, and January averages a low around 21°F. That’s a lot of heating hours to get the sizing wrong. Most installs take 4 to 8 hours, so you’re usually warm again the same day, and your original hardwood and plaster stay protected while the old system comes out.
Dempsey Energy is an HVAC and plumbing company with more than 12,000 customers across Massachusetts. Newton is a different kind of job than most. There are thirteen villages, from Newton Centre and Waban to Auburndale and Nonantum, and no single downtown setting the pattern. You’ll find Victorians and Greek Revivals in Waban and West Newton, and newer condos near Chestnut Hill.
That’s why gas furnace installation in Newton, MA begins with a visit, not a catalog. We measure, check your ducts, size the furnace, and tell you plainly whether you need a replacement or a repair.
Because we handle both heating and plumbing, we also notice when a boiler, water heater, or gas line overlaps with your furnace project. You get one company to call and a clear explanation of what the job involves before it starts.
New furnace installation in Newton, MA starts at your house, before any quote. We measure the space, look over the ductwork that’s already there, and size the furnace to the home you have today. This is also when we look for venting, gas line, or duct issues that would change the scope, so nothing surprises you on install day.
Next comes the permit. In Newton, gas work goes through the city’s Inspectional Services Department, and every permit has an inspector assigned to it. We handle the paperwork and schedule around you, so you don’t have to deal with City Hall.
On install day, we protect your floors and belongings, remove and dispose of the old system, and make whatever electrical and gas line changes the new one needs. Then we install to manufacturer specs and Massachusetts codes.
Before we call it done, we test the safety systems, check the gas connections for leaks, verify airflow, set up your thermostat, and commission the system. Then we schedule the municipal inspection. Your furnace isn’t finished until Newton’s inspector signs off, and you get warranty information and operating instructions before we leave.
Ready to get started?
Residential furnace installation in Newton, MA covers more than the furnace itself. You get sizing based on your house, removal and disposal of the old system, any electrical or gas line changes, safety and leak testing, thermostat setup, the permit, and the inspection. In Newton, that last part is real work. The city issues more than 1,200 gas permits in a typical year, and each one carries an inspector’s name and phone number.
Installation comes with warranty protection on both the equipment and the installation work. We stand behind the workmanship, and the manufacturer covers the equipment.
The Dempsey Comfort Club picks up where the install leaves off. Members get scheduled maintenance, annual tune-ups, priority scheduling, and discounts on repairs, which is worth having in a heating season that runs from early December to mid-March.
Scope changes from house to house. A Victorian in Waban or West Newton may need duct or venting changes that a newer building won’t, which is why we won’t put a number on heating system installation in Newton, MA before we’ve seen the place. If you’ve been searching for furnace installation near you and keep landing on cost guides instead of answers, ask for a quote and we’ll walk you through what’s in it.
For a typical Boston-area home, Angi puts the average new furnace at $6,396, with most people paying between $3,730 and $9,077. Labor makes up roughly $1,000 to $4,000 of that, and hauling away the old furnace adds $60 to $300. Those are typical ranges from a cost guide, not a quote from Dempsey Energy, and they aren’t specific to Newton.
What moves furnace installation cost in Newton, MA up or down is mostly the house. Heat load, the condition of your ductwork, venting changes, gas line work, the efficiency of the unit you pick, and permits all end up in the final number. In a house with decades of additions and updates—common in Newton’s older neighborhoods—the ducts and venting are where surprises tend to hide.
That’s why we look at them before we price anything. You get a written estimate after the in-home assessment, with the scope spelled out.
Yes. A gas furnace replacement in Newton needs a permit, and gas permits go through the city’s Inspectional Services Department. Newton issues more than 1,200 gas permits in a typical year, and each one has an inspector’s name and phone number on it. A real person signs off on your install.
You don’t have to fill out the forms. We handle the permit as part of furnace installation in Newton, MA and schedule the municipal inspection once the system is tested and running.
One thing worth knowing: in Massachusetts, gas work has to be done under a licensed gas fitter, and the permit is pulled by someone holding the proper master license. When you’re comparing quotes, ask each contractor who pulls the permit and whether it’s included in the price. If someone suggests skipping it, keep looking.
Most furnace replacement in Newton, MA takes 4 to 8 hours once the crew is on site, so you’re usually not without heat overnight. That’s the standard range, and independent cost guides say the same.
Older houses are where the time can stretch. If the venting, gas line, or ductwork needs changes, the job takes longer. That’s why we do the measuring and duct check before install day instead of finding out with the old furnace already out. We’d rather explain a change in scope to you before the work than after.
Timing matters here, too. Newton’s cold season runs from early December to mid-March, and January lows average around 21°F. If you’re planning ahead rather than reacting to a breakdown, spring and summer give you a calmer window to compare quotes and pick a date.
It depends on what you heat with now. Newton’s own residential energy sheet says that for homes heating with natural gas, a heat pump will likely cost more to run than the current system. It also says Mass Save is offering whole-home heat pump rebates of up to $8,500 for systems installed in 2026, plus 0% financing. The federal electrification tax credits expired at the end of 2025.
Newton adopted a Fossil Fuel-Free Ordinance in 2024, which lets the city require electric heating in new buildings and substantial renovations. If your project is a major renovation, ask Inspectional Services what applies before you pick equipment.
Dempsey Energy also offers heat pump service, so we can lay out gas furnace installation in Newton, MA and a heat pump side by side. You can also ask us about current Mass Save incentives.
Gas furnaces typically last 15 to 20 years, so a 15-year-old unit is in the zone but not necessarily done. After about year 10, efficiency slips roughly 1 to 2% a year, so an older furnace can cost more to run even while it works. Consumer Reports’ general advice is that repair usually makes more sense unless a key part like the heat exchanger or control module fails, especially on a unit past 15 years.
So here’s the honest version. If it’s a smaller repair on a furnace that’s been reliable, fix it. If the heat exchanger is cracked, the repairs keep coming, or you’re facing a big repair on an older unit, that money is better spent on new furnace installation.
Either way, replace only what’s broken. If your A/C works fine, the furnace job doesn’t need to touch it.
Workmanship issues are handled by Dempsey Energy, and equipment issues are handled by the manufacturer. At the end of the job, we go over the warranty information and operating instructions so you know who to call for what.
After that, the Dempsey Comfort Club is how we stay in the picture. Members get scheduled maintenance, annual tune-ups, priority scheduling, and discounts on repairs. With a heating season that runs from early December to mid-March, a fall tune-up is a simple way to catch problems before January.
One more note that applies in Newton. The city’s energy sheet points out that heating systems of all fuel types stop working in a power outage, because the fans, ignition, and controls need electricity. A new furnace won’t change that, and we’d rather you hear it from us now than find out during a winter storm.
Local Resources
Useful Links
Other Services we provide in Newton
